Blue Whale Trees
Find my tree

Can trees block road noise? What a planting cuts, how deep the belt must be, and the native evergreens for it

By · Published · 6 min read

How many decibels a strip of trees takes off traffic sound, why a lone hedge disappoints, what a berm or wall adds, and which native evergreens fill a screen.

On this page How much a belt of trees takes offWhere the cut comes fromWhy two federal guides disagreeWhat makes a belt workA berm or a wall does more, and trees on it do mostNative evergreens for a noise beltPlanting the beltCommon questionsSources

Trees quiet a road only when they stand in a deep, dense belt. A planted belt 100 feet deep cuts traffic noise by 5 to 8 decibels, and a 12-foot berm inside it raises the cut to 10 to 15. One or two rows of trees make no appreciable difference. A belt that works in winter is built of evergreens, with dense shrubs along its edges.

Interstate 95 running between tall woods on the left and a long concrete noise wall on the right, with cars and trucks
Interstate 95 in Stafford County, Virginia, in September 2023, with woods on one side and a noise wall on the other. About 100 feet of dense woods cuts about 5 decibels. Photo: DiscoA340, CC BY-SA 4.0 (source)

How much a belt of trees takes off

A change of less than 3 decibels is too small for most ears to notice. Highway noise walls usually cut 5 to 10 decibels, which makes traffic sound up to half as loud. Thirty meters of dense vegetation, about 100 feet, takes off about 5, the cut of a wall just tall enough to hide the traffic.

In Cook and Van Haverbeke’s tests, recorded truck noise sent through dense windbreak belts lost 5 to 8 decibels more than it did over the same ground without trees. Over open ground, heavy traffic grows only 3 decibels quieter each time the distance doubles. Distance alone would need two to four times as much open ground to match the belts.

Where the cut comes from

One model followed traffic noise through a belt 15 meters deep, about 50 feet. The soft forest floor alone took off about 3 decibels compared with a lawn. Trunks added a real cut once they stood less than 3 meters apart, about 10 feet, and grew more than 11 centimeters thick, about 4 inches. Shrubs added at most 2 decibels, in a band 50 feet deep, many times the thickness of a hedge. The leafy crowns took nothing off, since they bounced a little sound back down toward the ground.

Belts that can be planted in practice could match a thin wall 3 to 5 feet high. A single row that hides the road cuts little noise but may give a slight psychological benefit.

Why two federal guides disagree

The Federal Highway Administration, writing for highways, finds that enough trees will not fit along a road:

“Trees and other vegetation can be planted for psychological relief but not to physically lessen noise levels.” (Federal Highway Administration, Highway Traffic Noise Barriers at a Glance)

The National Agroforestry Center’s guide to buffers in rural and urban landscapes counts the same decibels as worth having:

“Buffers can reduce noise from roads and other sources to levels that allow normal outdoor activities to occur.” (USDA National Agroforestry Center, Buffers for Noise Control)

The difference is room. A highway seldom has 100 feet beside it to plant, while a farm or a large lot may.

What makes a belt work

The tests and the guide agree on these points:

  • Depth. For fast traffic, plant 65 to 100 feet of trees and shrubs, with middle rows that reach at least 45 feet.
  • Near the road. A belt works best near the noise rather than the house, with a setback for accidents and drifting snow. For highway traffic, the tests’ authors advised a near edge within 50 to 80 feet of the middle of the nearest lane.
  • No gaps. Plant as close as is practical, with shorter shrubs in front of taller trees, so that no one can see over or through the belt.
  • Evergreen rows. Evergreens control noise all year, while deciduous trees screen only in leaf.
  • Soft ground. Keep the floor in fallen leaves or tall grass rather than gravel or paving.
  • Length. Make the belt about twice as long as the distance from the road to the house, running equally far past it on each side.
  • Salt. Choose plants that stand road salt and fumes. The most tolerant go in the row nearest the road, where they also shield the rows behind from salt spray.
A broad American holly, dense with dark evergreen leaves nearly to the ground, beneath taller trees in fall
An American holly dense with evergreen leaves nearly to the ground on October 19, 2026. Evergreens give noise control the year round. Photo: Blue Whale Trees

A berm or a wall does more, and trees on it do most

A solid barrier just tall enough to hide the traffic cuts about 5 decibels, and each meter of height above that, about 3 feet, adds about 1.5 more. An earth berm cuts about 3 decibels more than a wall of the same height, though it takes a wide strip of land. Trees planted on a berm do considerably more than the berm or the trees alone. For slower traffic on town streets, Cook and Van Haverbeke advised a berm or solid barrier 6 to 8 feet high, with dense shrubs in front of it and taller trees behind.

A tan concrete noise wall running along the top of a grassy bank above a highway, with trees rising behind it
A noise wall on a grassy bank above Interstate 440 in Wake County, North Carolina, in August 2022. A barrier cuts about 5 decibels once it hides the traffic. Photo: DiscoA340, CC BY-SA 4.0 (source)

Native evergreens for a noise belt

These native evergreens grow tall enough for the middle rows, coldest zone first, at their spacing for a screen:

Plant Zones Height, feet Set apart, feet
Red spruce 2–6 60–75 12
Northern white cedar 2–7 40–60 10
Eastern red cedar 2–9 30–50 12
Eastern hemlock 3–7 40–100 15
Atlantic white cedar 3–9 40–60 10
American holly 5–9 20–50 15
Spruce pine 7–9 40–80 20

These evergreen shrubs and small trees fill the outer rows, coldest zone first:

Plant Zones Height, feet Set apart, feet
Inkberry 4–10 5–10 5
Devilwood 5–10 15–30 10
Florida anise 6–10 6–10 5
Yaupon 7–10 10–25 8
Odorless bayberry 7–10 10–20 8

Along a salted road, the row nearest the traffic takes eastern red cedar, devilwood or yaupon, which stand salt spray, or inkberry, which takes road salt. Northern white cedar, often planted along roads as a sound barrier, is very sensitive to salt, and eastern hemlock stands no salt spray, so both belong in the rows nearer the house. Where winters are too cold for inkberry, northern bayberry, a salt-tolerant shrub hardy to zone 3, fills the outer row by a salted road.

Atlantic white cedar and odorless bayberry suit ground that stays wet, and eastern red cedar dry, open ground. Blue Whale Trees grows every evergreen in the two tables.

Planting the belt

Put the shrubs in the outer rows and the tall evergreens in the middle. The windbreak plan gives the spacing between rows and the order of shrubs and trees. Then choose by the room you have:

  • 65 feet or more: a belt of the evergreens above, with shrubs along both edges.
  • A town lot: a solid fence or berm 6 to 8 feet high, dense evergreen shrubs on the road side and taller evergreens behind it.
  • Room for one row: evergreens that hide the road, planted for the view and the relief it brings rather than for decibels.

The tree finder lists the evergreen screens for your zone, sun and soil. Our evergreens and salt-tolerant natives have groups in the shop.

Common questions

Do evergreen trees block sound better than deciduous trees?

Evergreens keep working in winter, when a deciduous belt stands bare. In summer the leaves count for little: in one model, the crowns scattered a little sound back down instead of stopping it, while the soft ground and the trunks did the work.

Do trees absorb sound?

Partly: leaves, twigs and trunks scatter sound and cut its high pitches best. Much of a belt’s effect comes from the soft forest floor under it, which takes off about 3 decibels more than a lawn.

What are the best trees to block road noise?

Tall, dense evergreens in several rows, with evergreen shrubs in front to close the gaps near the ground. Eastern red cedar suits the row by a salted road, with northern white cedar, Atlantic white cedar or American holly behind it. Highway noise design texts count about 5 decibels per 100 feet of planting once the trees pass 15 feet and hide the road.

Will a fence block road noise better than trees?

For the room it takes, yes: a solid fence just tall enough to hide the traffic cuts about 5 decibels, as much as 100 feet of dense trees. An earth berm of the same height cuts about 3 decibels more, and trees planted on a berm do more than either alone.

Share Copy link Email this article

Tool

Find the right tree for the spot

Filter everything we grow by hardiness zone, mature size, sun, soil and what you want the plant to do.

Open the tree finder

Shipping windows, newly priced plants and new articles. Four to six emails a year, and nothing else.

Sources

(5 references)
  • Highway Traffic Noise Barriers at a Glance: Federal Highway Administration (updated October 6, 2021): the quotation on planting for psychological relief, about 5 decibels from 30 meters of dense vegetation that cannot be seen over or through, barriers cutting 5 to 10 decibels and up to half the loudness, 5 decibels once a barrier hides the traffic and about 1.5 more per meter of height, berms 3 decibels better than walls of the same height but needing much land, and changes under 3 decibels too small to hear.
  • Buffers for Noise Control: USDA National Agroforestry Center, Conservation Buffers: Design Guidelines for Buffers, Corridors, and Greenways, guideline 6.4: the quotation on buffers and outdoor activities, 5 to 8 decibels from a 100-foot planted buffer and 10 to 15 with a 12-foot landform, a buffer close to the noise with a setback for accidents and drifting snow, evergreens for year-round control, a dense buffer of trees and shrubs, and plants tolerant of air pollution and de-icing.
  • Effectiveness of Trees and Vegetation in Reducing Highway Noise: A Literature Review (PDF): Virginia Highway Research Council (E. G. Kerby II, January 1974): one or two rows of trees making no appreciable cut and their slight psychological benefit, the tests through windbreak belts in Cook and Van Haverbeke’s 1971 bulletin, with their 5 to 8 decibels and their advice on depth, distance from the lane, height, density, soft ground, length, evergreens, tree-covered landforms and a 6- to 8-foot barrier for town traffic, 3 decibels per doubling of distance, the design value for trees 15 feet tall, and the better cut of high-pitched sound.
  • Road traffic noise shielding by vegetation belts of limited depth (PDF): Ghent University, the authors’ revised manuscript of T. Van Renterghem, D. Botteldooren and K. Verheyen, Journal of Sound and Vibration 331 (2012): a modeled belt 15 meters deep, about 3 decibels from the forest floor over grassland, trunks less than 3 meters apart and more than 11 centimeters thick, shrubs at most 2 decibels, crowns scattering a little sound back down, and practical belts able to match a thin wall 1 to 1.5 meters high.
  • Minimize Deicer Damage with Salt Tolerant Plants: Penn State Extension (Mary Jo R. Gibson, updated June 8, 2026): arborvitae planted along roads as windbreaks and sound barriers and very sensitive to salt, eastern red cedar tolerating salt spray and soil-borne salt, and salt-tolerant trees shielding sensitive ones from salt spray.

Keep reading

Related articles

All articles